C18 ACERT™ Offshore Production Engine

Cat C18 ACERT™ Fire Pump Engines. Ratings: 447-597 bkW (600-800 bhp)@ 1800-1900 rpm meet U.S. EPA Tier 3 or U.S. EPA Tier 2 emission standards for stationary emergency fire pump engines. Rating: 522 bkW (700 bhp) @ 1500 rpm is Non-certified. FM Approved. UL Listed.

Request a Quote
Minimum Rating
600.0 bhp
Maximum Rating
800.0 bhp
Emissions
U.S. EPA Tier, Tier 2 or non-certified
Bore
5.7 in

Videos not available for this product.

360 View not available for this product.

Product Specs

Engine Specifications

Minimum Rating
600.0bhp
Maximum Rating
800.0bhp
Emissions
U.S. EPA Tier, Tier 2 or non-certified
Bore
5.7in
Stroke
7.2in
Displacement
1106.0in3
Aspiration
Turbocharged-Aftercooled
Rotation (from flywheel end)
Counterclockwise
Rated Speed
1750r/min
Engine Weight - Net Dry
3900lb
Oil Change Interval
500h
Flywheel and Flywheel Housing
SAE No. 1
Flywheel Teeth
113
Minimum Rating
600BHP
Maximum Rating
800BHP
Emissions
U.S. EPA Tier, Tier 2 or non-certified
Bore
5.7in
Stroke
7.2in
Displacement
1106in³
Aspiration
Turbocharged-Aftercooled
Rotation from Flywheel End
Counterclockwise

Dimensions

Length
74.4in
Width
43.0in
Height
54.3in
Length
74.4in
Width
43in
Height
54.3in

Capacity for Liquids

Lube Oil System - Refill
10gal (US)
Cooling System - Engine
13.3gal (US)

Standard/Optional Features

Standard Equipment:

  • Air Inlet System
    • Dual turbocharger: front and rear inlet 127.mm (5.0 in)
    • Separate Circuit Aftercooled (SCAC)
  • Charging System
    • Charging alternator 24 volt, 50 amp
  • Control System
    • Dual Electronic Control Units (ECU), primary and secondary
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold start capability to -20° C (-4° F)
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and total engine limit
    • Electronic diagnostics and fault logging
    • Engine monitoring system SAE J1939 broadcast and control
  • Cooling System
    • Thermostats and housing, vertical outlet
    • Jacket water pump, centrifugal
    • Heat exchanger installed
    • Expansion tank
  • Exhaust System
    • Exhaust manifold, dry
    • Dual turbo: exhaust elbow, dry 203 mm (8 in)
  • Flywheels And Flywheel Housing
    • SAE No. 1 flywheel
    • SAE No. 1 flywheel housing
    • Power take-off (PTO) flywheel stub shaft
  • Fuel System
    • Electronic unit injector
    • Fuel filter, secondary (2 micron high performance)
    • Fuel transfer pump
    • Fuel priming pump
    • Fuel sample valve, mounted on fuel filter base
    • Primary fuel filter
    • Water separator
  • Instrumentation
    • Instrument panel, LH
    • Engine oil pressure gauge
    • Voltmeter gauge
    • Water temperature gauge
    • Tachometer/engine hour meter
  • Lube System
    • Open crankcase ventilation system
    • Oil cooler
    • Lube oil filter
    • Front sump oil pan
    • Oil filler
    • Oil dipstick
    • Oil pump
  • Mounting System
    • Front and rear support
  • Protection System
    • Stop-Start System, automatic (compatible with NFPA 20 requirements, able to be energized from either of two battery sources and capable of manual starter actuation)
  • Starting System
    • 24 volt, LH electric starting motor
    • Jacket water heater (3 kW, 120-240 volt)
  • General
    • Vibration damper
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit, 70 pin connector (connectors, pins, sockets)

Optional Equipment: