Cat® C1.5 Industrial Power Unit
The Cat® C1.5 Industrial Power Unit is offered in the following rating: 27 bkW (36 bhp) @ 2800 rpm. This rating meets U.S. EPA Tier 4 Final emission standards. Rating: 24.2 bkW (32.5 bhp) @ 3000 meets EU Stage IIIA (U.S. EPA Tier 4 Interim) emission standards. Conveniently pre-configured for a wide range of applications, the Cat® Industrial Power Unit is a complete power package containing a radiator, flywheel, alternator and alternator wiring completely pre-assembled for fast, straightforward installation in a number of OEM, customer and packager applications. These fuel efficient units are ready made for irrigation, industrial, mining and other pump applications.
Request a Quote
Product Specs
Power Rating
- Minimum Power
- 33.7bhp
- Maximum Power
- 36.0bhp
- Rated Speed
- 2800-3000 rpm
- Minimum Power
- 33.7HP
- Maximum Power
- 36HP
- Rated Speed
- 2800-3000 rpm
- Maximum Torque
- 69.6lb-ft @ 1800 rpm
Emission Standards
- Emissions
- U.S. EPA Tier 4 Final or EU Stage IIIA
- Emissions
- U.S. EPA Tier 4 Final or EU Stage IIIA
General
- Engine Configuration
- Inline 3, 4-Stroke-Cycle Diesel
- Bore
- 84 mm (3.3 in)
- Stroke
- 90 mm (3.5 in)
- Displacement
- 1.496 L (91 in³)
- Aspiration
- Naturally Aspirated (NA)
- Compression Ratio
- 22.5:1
- Rotation (from flywheel end)
- Counterclockwise
- Cooling System Capacity
- 5.98 L (6.3 qt)
- Lube System (refill)
- 6 L (6.3 qt)
- Engine Configuration
- Inline 3, 4-Stroke-Cycle Diesel
- Bore
- 84 mm (3.3 in)
- Stroke
- 90 mm (3.5 in)
- Displacement
- 1.496 L (91 in³)
- Aspiration
- Naturally Aspirated (NA)
- Compression Ratio
- 22.5:1
- Rotation from Flywheel End
- Counterclockwise
- Cooling System - Capacity
- 5.98 L (6.3 qt)
- Lube System - Refill
- 6 L (6.3 qt)
- Bore
- 3.3in
- Stroke
- 3.5in
- Displacement
- 91in³
- Aftertreatment
- -
Aftertreatment Dimensions (Approximate. Final dimensions dependent on selected options)
- Weight
- 13 kg (28.7 lb)
Power Unit Dimensions - Approximate
- Length
- 820 mm (32.3 in)
- Width
- 497 mm (19.6 in)
- Height
- 793 mm (31.2 in)
- Weight - Approximate, Net Dry - Standard Configuration Without Oil, Cooling, Clutch, Compressor, A/C
- 175 kg (385.8 lb)
Aftertreatment Dimensions - Approximate
- Weight
- 13 kg (28.7 lb)
Power Unit Dimensions
- Length
- 32.3in
- Width
- 19.6in
- Height
- 31.2in
- Weight
- 386lb
Aftertreatment Dimensions
- Weight
- 28.7lb
Standard/Optional Features
Standard Equipment:
-
- Air Inlet System
-
- Inlet manifold
-
- Control System
-
- Alternator 12 volt 65 amp
- Starter motor 12 volt
- Glow plug starting aid
- Tier 4 Final: Alternator 12V 85 amp
-
- Cooling System
-
- Belt-driven coolant pump
- Coolant temperature switch
- Mounted air cleaner
- Mounted radiator and fan
-
- Flywheel & Flywheel Housing
-
- Naturally Aspirated: SAE No. 7 1/2 flywheel
- Choice of SAE No. 4, SAE No. 5 or standard backplate flywheel housing
-
- Fuel System
-
- Fuel injection pump
- Fuel filter
- Electronic Shut-off Solenoid (ESOS)
-
- Lube System
-
- Spin-on lube oil filter
- Lube oil pressure switch
- Lube oil sump
-
- Power Take Off (pto)
-
- Provision for timing case rear facing PTO
-
- General
-
- Cast iron, engine block
- Cast iron exhaust manifold--side outlet
- Cold start capability to -20° C (-4° F)
- Gradeability 35° continuous
- Paint: Caterpillar yellow, with optional colors available at request
-
- Tier 4 Final Aftertreatment / Clean Emissions Control Equipment
-
- Diesel Particulate Filter (DPF)
- Diesel Oxidation Catalyst (DOC)
- Passive regeneration system with backup